change stable to stretch, makes more sense

[automated-distro-installer] / fai / config / hooks / partition.DEFAULT

diff --git a/fai/config/hooks/partition.DEFAULT b/fai/config/hooks/partition.DEFAULT
index f241fd608f3c8c72524e6c1b3ab9097cd78b2e7b..fdcfe6d1238e2f5f0c98d3f123fe4746b1a1ba1b 100755 (executable)
--- a/fai/config/hooks/partition.DEFAULT
+++ b/fai/config/hooks/partition.DEFAULT
@@ -195,16 +195,16 @@ fi
 
 
 if [[ ! $DISTRO ]]; then
-    if ifclass VOL_STABLE_BOOTSTRAP; then
-        DISTRO=debianstable_bootstrap
+    if ifclass VOL_STRETCH_BOOTSTRAP; then
+        DISTRO=stretch_bootstrap
     elif ifclass VOL_STRETCH; then
-        DISTRO=debiantesting
-    elif ifclass VOL_STABLE; then
-        DISTRO=debianstable
+        DISTRO=debianstretch
     elif ifclass VOL_XENIAL; then
         DISTRO=ubuntuxenial
     elif ifclass VOL_BELENOS; then
         DISTRO=trisquelbelenos
+    elif ifclass VOL_FLIDAS; then
+        DISTRO=trisquelflidas
     else
         echo "PARTITIONER ERROR: no distro class/var set" >&2
         exit 1
@@ -233,7 +233,7 @@ fi
 if ifclass tp; then
     lukspw=$(cat $luks_dir/traci)
 else
-    lukspw=$(cat $luks_dir/ian)
+    lukspw=$(cat $luks_dir/iank)
 fi
 if ifclass demohost; then
     lukspw=x
@@ -283,19 +283,28 @@ if $partition; then
         parted -s $dev mklabel gpt
         # MiB because parted complains about alignment otherwise.
         pcmd="parted -a optimal -s -- $dev"
-        $pcmd mkpart primary "ext3" 12MiB ${root_end}MiB
-        $pcmd mkpart primary "linux-swap" ${root_end}MiB ${swap_end}MiB
+        $pcmd mkpart primary ext3 12MiB ${root_end}MiB
+        # without naming, systemd gives us misc errors like:
+        # dev-disk-by\x2dpartlabel-primary.device: Dev dev-disk-by\x2dpartlabel-primary.device appeared twice
+        $pcmd name $rootn root
+        # normally a swap is type "linux-swap", but this is encrypted swap. using that
+        # label will confuse systemd.
+        $pcmd mkpart primary "" ${root_end}MiB ${swap_end}MiB
+        $pcmd name $swapn swap
         $pcmd mkpart primary "" ${swap_end}MiB ${disk_mib}MiB
+        $pcmd name $bootn boot
         # i only need a few k, but googling min size,
         # I found someone saying that gparted required
         # required at least 8 because of their hard drive cylinder size.
         # And 8 is still very tiny.
         $pcmd mkpart primary "ext2" 4MiB 12MiB
+        $pcmd name $grub_extn grubext
         # gpt ubuntu cloud image uses ~4 mb for this partition. fai uses 1 MiB.
         # so, I use 3, whatever.
         # note: parted manual saying cheap flash media
         # should to start at 4.
         $pcmd mkpart primary "" 1MiB 4MiB
+        $pcmd name $bios_grubn biosgrub
         $pcmd set $bios_grubn bios_grub on
         $pcmd set $bootn boot on # generally not needed on modern systems
         # the mkfs failed before on a vm, which prompted me to add
@@ -354,7 +363,7 @@ else
 fi
 
 
-if [[ $DISTRO != debianstable_bootstrap ]]; then
+if [[ $DISTRO != stretch_bootstrap ]]; then
     # bootstrap distro doesn't use separate encrypted root.
     mount -o subvolid=0 $first_root_crypt /mnt
     # systemd creates subvolumes we want to delete.
@@ -392,7 +401,7 @@ btrfs subvolume set-default 0 /mnt # already default, just ensuring it.
 mkdir -p /mnt/grub2
 cp $FAI/distro-install-common/libreboot_grub.cfg /mnt/grub2
 
-if [[ $DISTRO == debianstable_bootstrap ]]; then
+if [[ $DISTRO == stretch_bootstrap ]]; then
     # this is just convenience for the libreboot_grub config
     # so we can glob the other ones easier.
     boot_vol=$DISTRO
@@ -411,7 +420,7 @@ grub-editenv /mnt/grubenv set did_fai_check=true
 grub-editenv /mnt/grubenv set last_boot=/$boot_vol
 umount /mnt
 
-if [[ $DISTRO == debianstable_bootstrap ]]; then
+if [[ $DISTRO == stretch_bootstrap ]]; then
     cat > /tmp/fai/fstab <<EOF
 $first_boot_dev  /  btrfs  noatime,subvol=$boot_vol  0 0
 EOF